![]() ![]() ![]() Power reset for Android TV™ or Google TV™ models.Depending on the cause, this issue is often resolved by performing a power reset on your TV.If model-specific information is needed to perform any action, check your product Troubleshooting stepsĬheck if the audio and video sync issue is resolved after completing each step. In this case, the issue is not with the TV speakers. Safety & Compliance: /complianceĪ: 9300 S.W.Note: If the TV is connected to a soundbar or home theater system with an HDMI or optical cable, the sound may be delayed due to the audio processing delays in the soundbar or home theater system. Do not spray any cleaning product directly on the bar. Power Supply: (PS-12-60) 60W power supply with cordįactory reset: Press & hold the Launch button for 10 seconds to revert the bar to factory settings.Ĭleaning: Use a soft cloth to wipe off dust. ![]() Video – Camera LED: VBC only – above camera (behind the glass)Īctive with camera ON – LED ON – White, shutter openĪctive with camera OFF – LED OFF, shutter openĭisplay Mount: (PMA 2000-DM) allows bar to be mounted on a video display Pressing the Launch button customizes the audio coverage based on the room’s characteristics.Īudio – Microphone LEDs: center front (behind the glass) The file must be downloaded from the Biamp website first and then the firmware update can be initiated from the software.īiamp Launch is the smart technology to optimize the audio for the room. This software is used to facilitate firmware updates to both bar models, and can provide additional camera controls for the VBC bar. Audio and video control is available to the connected host device’s operating system and conferencing apps.īiamp’s Camera Controller software can be downloaded (Mac or PC). The Parlé Conference bars act as USB peripherals that are connected to USB host devices. Rotate the bar up – back into position, and remove the film covering the center glass.Note: Connect cables and power as noted in Steps 1-3 on the previous page. Secure the bar with screws as shown (2 on each hinge).Hang the bar on the wall plate knobs and move it down to capture the knobs. Position the bar face down and rotate the hinge plates up 90°.Use the wall plate to mark the locations, and install the anchors in the wall.Reserve the (4) screws for reattachment to the wall plate. Press the Launch button (location shown), and allow the smart technology to optimize the audio for the room.Position the bar facing the conference table / occupants, and remove the film covering the center glass.The stubs will provide strain relief for the cables. Reinstall the input cover, routing the cords through the plastic stubs and the opening at the bottom of the cover.If auxiliary power is necessary, connect the power supply to the threaded port, then plug the power supply into the wall. Connect the other end to the host device. Connect the USB-C cable and secure with the screw.Pull out and remove the back panel cover to expose the power connections.If the host device cannot provide 60W, an optional Biamp auxiliary power supply (PS-12-60) must be used. The bars can be powered through the USB-C port, but the host device must be able to supply 60W over USB-C. Clear an area on a table or stand (usually under the video display). The bar is shipped with the table mount attached. See Status Indicators section (pg 5) for behavior and the associated LED state. Parlé VBC 2500 or ABC 2500 conferencing bar.VBC 2500 – Electric Pan/Tilt/Zoom with 5x zoom and auto framing technology to keep participants in frame CONTENTS.Biamp Launch automated tuning system to optimize audio.LED indicators for audio and video status.Deep learning noise reduction algorithm for clear voice reproduction.Beamtracking microphone technology actively tracks and intelligently mixes conversations.Parlé VBC 2500 and ABC 2500 are all-in-one conferencing bars featuring Biamp Audio Intelligence to deliver premium audiovisual experiences for small and medium conference rooms. 7.1 Related Manuals / Resources PRODUCT DESCRIPTION
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |